Kensight Serrated Ramp Front GlockSight - SMALL and LARGE Frame
Kensight SightsWrite a Review
Kensight Sights
Kensight Serrated Ramp Front GlockSight - SMALL and LARGE Frame
Because the Glocks rear dovetail, on the small and full frame, is small, shallow and not generally seen as ideal for an adjustable sight, it is anything but ideal for adding an adjustable. Knowing this, Kensight has designed one fully adjustable rear for all of the Glock pistols. Because the Glocks slide don't have a deep cut so that the fully adjustable sight with it's many mechanisms can "seat" down low enough to be paired with a standard height front.
All of the sights below are fully serrated from bottom to top and very simple to install with a single mounting screw (included) and a small bit of blue locktite if desired.
Front sight Kensight® item# 870-927. It is .315" tall, the minimum required for the adjustable rear, .100" wide. It is an all around good height and is a good height for target shooting at standard distances. Because it is our lowest height front sight, holstering is easier on a wider range of holsters than our other heights
Front sight is Kensight® item# 870-929. It is .330", .100" wide and .100" wide. This taller height is better for targets at longer distances.
Front sight is Kensight® item# 870-931. It is .350, the tallest of the three sights, and .100" wide. This sight was designed for again shooting at greater distances but to be paired with suppressors.
Authentic Kensight ® Sights - The Professional's Choice
This is an authentic Kensight ® sight, and not to be confused with other brands. When it comes to durability, and features the Kensight® sights far exceed our competitors. Our sights are Wire-EDM machined from a single billet of 4140 chrome-moly steel. The result is a precision sight built with better materials and the Wire-EDM construction ensures the tightest tolerances possible. This translates to ultra-smooth adjustments, audible clicks for both windage and elevation, and consistent dovetail dimensions in which the "industry standard" CNC construction cannot compete. Backed by our Limited Lifetime Warranty, Kensight 1911 sights are premium quality and the first choice for factory-fit OEM manufactures, competition shooters and professional's worldwide.
Limited Lifetime Warranty
We stand behind our products. All Kensight Sights are covered by a limited lifetime warranty. We guarantee our products against defects in material and construction. This limited lifetime warranty does not extend to normal signs of wear. It does not cover breakage, damage or rust due to misuse, improper maintenance, accidents, loss or theft. The warranty does not extend to damages cause by unauthorized repairs.
Any product we determine to be defective will be repaired or replaced solely at our discretion. To receive warranty repair or replacement, the owner must send the product to be evaluated by KFS Industries Warranty Services located at our Atlanta, Georgia headquarters. In addition to the provisions of this warranty, the owner may also have other rights that can vary by state. No other warranties are implied or expressed other than what is specifically stated here.
Warranty Service
All products returned to KFS Industries for a warranty claim must have prior approval of a KFS Customer Service employee in the form of a Return Material Authorization Number (RMA). The RMA must be displayed on the exterior of the return carton. Merchandise returned without an RMA will be refused. The RMA number assigned will expire 30 days from date of issue. To obtain an RMA, please call the KFS Atlanta, Georgia headquarters at (404) 691-7611.
After you obtain your RMA, Please send your product to:
KFS Industries Inc.875 Wharton Dr SW
Atlanta, GA 30336
You must pay the shipping and insurance costs to return your product to KFS Industries Inc., and we will pay the shipping charges to return the product to your US address only. All International shipping will be the responsibility of the consumer.
Upon receipt of a returned product, we will verify warranty coverage. If the product is not covered by warranty, KFS Industries Inc. will send you an estimate of the cost to repair your product prior to performing any services not covered.
- Product Series:
- Glock Series
- Material:
- 4140 Chrome Molly Steel
- Color:
- Black
- Construction:
- Wire-EDM Machined
- Finish:
- Black Oxide
- Dovetail:
- Glock
- Blade Type:
- Serrated
- Blade Height:
- 0.315"-0.350"
- Blade Width:
- 0.100"
- Sight Base:
- Glock-Style